24BDMFPK
RF Central
24BDMFPK
RF Central 2.4GHz Broadcast Digital Microwave SD/HD Field Kit
This system uses the RF Central RFX-PMR-II 2.4GHz field receiver, which has a built-in block down-converter and can decode CVBS, SD-SDI or HD-SDI. It operates in 2.4GHz and includes both a high gain omni-directional and sector RX antennas. Its companion is the RF Central RFX-CMT-II 2.4GHz camera-mounted transmitter.
This field kit offers the lowest latency of any professional system VER provides, 73mS end to end. It supports 720p or 1080i in HD mode.
This field kit offers the lowest latency of any professional system VER provides, 73mS end to end. It supports 720p or 1080i in HD mode.
Note: The VER team recommends that you take advantage of our expertise by consulting with one of our wireless video engineers before each rental. Please ask your rental agent to facilitate this discussion. We look forward to satisfying your wireless video needs
Technical Tools
PDF Documents
Manufacturer Specs
General
Frequency: 2.4GHz
Tuning Range/Frequency Selection: Selectable via side panel in 0.25 MHz steps
Transmit Power: 100 mw
Transmit Antenna: 4dBi gain typical (shown)
Modulation: COFDM DVB-T (2k carrier)
Modulation Modes
QPSK, 16QAM, 64QAM
FEC 1/2, 2/3, 3/4, 5/6, 7/8
Guard interval 1/4, 1/8, 1/16, 1/32
Data Rate: 5.5 to 31.7 Mbit/s
Bandwidth: 6, 7, and 8 MHz
Frequency Tolerance: 2.0 PM
Encoding: MPEG-2 Video (ISO/IEC 13818-2)
Latency: Low or Std Delay
Data Port Interface: DVB-ASI
Video Input
Digital
HD-SDI-SMPTE - 292m (with HD upgrade)
SD-SDI-SMPTE - 259m
ASI
Analog: NTSC/PAL composite
Supported Video Profiles
SD: 422P@ML, MP @ ML, SP@ML
HD: MP@HL 720p to 1080i
Sampling: 4:2:0 or 4:2:2
Audio Input
2 x analog inputs, mic/line selectable, digital AeS, SDI-embedded
Mechanical Interface
Transmitter normally mounts between battery and camera interface plate.
Available with interface plates to suit Anton Bauer or other mounts (specified at time of order).
Physical
Temperature: -4 to 122°F
Altitutude: 14,500 ft
Humidity: 95% long term
Power Requirements: 10-35 VDC ≤ 18w via Battery Plate or 4-pin lemo socket
Frequency: 2.4GHz
Tuning Range/Frequency Selection: Selectable via side panel in 0.25 MHz steps
Transmit Power: 100 mw
Transmit Antenna: 4dBi gain typical (shown)
Modulation: COFDM DVB-T (2k carrier)
Modulation Modes
QPSK, 16QAM, 64QAM
FEC 1/2, 2/3, 3/4, 5/6, 7/8
Guard interval 1/4, 1/8, 1/16, 1/32
Data Rate: 5.5 to 31.7 Mbit/s
Bandwidth: 6, 7, and 8 MHz
Frequency Tolerance: 2.0 PM
Encoding: MPEG-2 Video (ISO/IEC 13818-2)
Latency: Low or Std Delay
Data Port Interface: DVB-ASI
Video Input
Digital
HD-SDI-SMPTE - 292m (with HD upgrade)
SD-SDI-SMPTE - 259m
ASI
Analog: NTSC/PAL composite
Supported Video Profiles
SD: 422P@ML, MP @ ML, SP@ML
HD: MP@HL 720p to 1080i
Sampling: 4:2:0 or 4:2:2
Audio Input
2 x analog inputs, mic/line selectable, digital AeS, SDI-embedded
Mechanical Interface
Transmitter normally mounts between battery and camera interface plate.
Available with interface plates to suit Anton Bauer or other mounts (specified at time of order).
Physical
Temperature: -4 to 122°F
Altitutude: 14,500 ft
Humidity: 95% long term
Power Requirements: 10-35 VDC ≤ 18w via Battery Plate or 4-pin lemo socket