MM-4XP
Meyer Sound
MM-4XP
Meyer MM-4XP Powered Speakers
This miniature self-powered loudspeaker is designed for high-quality distributed systems. With its compact aluminum enclosure, the MM-4XP is especially suitable for installations involving space limitations and visibility concerns.
The loudspeaker’s proprietary 4-inch cone transducer delivers an impressive maximum peak SPL of 113 dB (measured with music referred to 1 meter), and has a wide operating frequency range of 120 Hz to 18 kHz with very low distortion, exhibiting the same high intelligibility and flat frequency and phase responses for which Meyer Sound loudspeakers are known. Peak and rms limiters regulate loudspeaker temperatures and excursion, ensuring that the MM-4XP performs exceedingly well even when driven into overload.
The loudspeaker's amplifier and signal-processing circuits are designed to store DC power and tolerate voltage drops, thereby accommodating light-gauge cables and long cable runs. Balanced audio and DC power are delivered through a sealed SwitchCraft® EN3™ 5-pin male connector on the rear panel, ensuring protection against harsh environmental conditions when the MM-4XP is installed outdoors.
The MM-4XP’s extruded aluminum enclosure acts as a heat sink to dissipate heat from the driver's voice coil.
MM-4XP loudspeaker systems require an MPS-488 external power supply.
The loudspeaker’s proprietary 4-inch cone transducer delivers an impressive maximum peak SPL of 113 dB (measured with music referred to 1 meter), and has a wide operating frequency range of 120 Hz to 18 kHz with very low distortion, exhibiting the same high intelligibility and flat frequency and phase responses for which Meyer Sound loudspeakers are known. Peak and rms limiters regulate loudspeaker temperatures and excursion, ensuring that the MM-4XP performs exceedingly well even when driven into overload.
The loudspeaker's amplifier and signal-processing circuits are designed to store DC power and tolerate voltage drops, thereby accommodating light-gauge cables and long cable runs. Balanced audio and DC power are delivered through a sealed SwitchCraft® EN3™ 5-pin male connector on the rear panel, ensuring protection against harsh environmental conditions when the MM-4XP is installed outdoors.
The MM-4XP’s extruded aluminum enclosure acts as a heat sink to dissipate heat from the driver's voice coil.
MM-4XP loudspeaker systems require an MPS-488 external power supply.
Product Weight: 4.2 lbs
Dimensions: 4.04”W x 4.04”H x 5.72”D
Technical Tools
PDF Documents
Manufacturer Specs
General
Operating Frequency Range: 120 Hz – 18 kHz
Note: Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.
Frequency Response: 160 Hz – 16 kHz ±4 dB
Note: Measured free-field with pink noise at 1 meter, 1/3 octave resolution.
Maximum Peak SPL: 113 dB
Note: Measured free-field with music and referred to 1 meter.
Dynamic Range 100 dB
Note: Taken from peak SPL referred to A-wtd noise floor.
Phase Response: 700 Hz – 17 kHz ±45°
Coverage
80°: 3 kHz – 14 kHz ±10°
120°: below 2 kHz
Transducer: One 4” cone driver
Input
Level: Audio source must be capable of producing +16 dBV (6.3 Vrms, 9.0 Vpeak) into 600Ω to produce maximum peak SPL over the operating bandwidth of the loudspeaker.
Impedance: 10 kΩ electronically balanced
Nominal Input Sensitivity: –2.5 dBV (0.75 Vrms, 1.0 Vpeak) continuous average is typically the onset of limiting for noise and music.
Power
Voltage Requirement: 48 VDC from external power supply MPS-488
Audio/Power Connector: Single EN3 5-pin male (3 pins for balanced audio, 2 pins for DC power)
Current Draw: 0.7 A average, 2.2 A peak
LED: To indicate loudspeaker status
Physical
Enclosure: Extruded aluminum with painted steel grille
Operating Frequency Range: 120 Hz – 18 kHz
Note: Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.
Frequency Response: 160 Hz – 16 kHz ±4 dB
Note: Measured free-field with pink noise at 1 meter, 1/3 octave resolution.
Maximum Peak SPL: 113 dB
Note: Measured free-field with music and referred to 1 meter.
Dynamic Range 100 dB
Note: Taken from peak SPL referred to A-wtd noise floor.
Phase Response: 700 Hz – 17 kHz ±45°
Coverage
80°: 3 kHz – 14 kHz ±10°
120°: below 2 kHz
Transducer: One 4” cone driver
Input
Level: Audio source must be capable of producing +16 dBV (6.3 Vrms, 9.0 Vpeak) into 600Ω to produce maximum peak SPL over the operating bandwidth of the loudspeaker.
Impedance: 10 kΩ electronically balanced
Nominal Input Sensitivity: –2.5 dBV (0.75 Vrms, 1.0 Vpeak) continuous average is typically the onset of limiting for noise and music.
Power
Voltage Requirement: 48 VDC from external power supply MPS-488
Audio/Power Connector: Single EN3 5-pin male (3 pins for balanced audio, 2 pins for DC power)
Current Draw: 0.7 A average, 2.2 A peak
LED: To indicate loudspeaker status
Physical
Enclosure: Extruded aluminum with painted steel grille