WFM700HD
Tektronix
WFM700HD
Tektronix WFM700HD High Definition Waveform/Vector Monitor
This unit offers the monitoring capabilities needed in the production, post-production, distribution, and transmission of high-definition digital video content.
It provides tools necessary for operational monitoring tasks like checking signal validity and content quality, setting levels, and verifying signal paths, all with the measurement accuracy, repeatability, and stability achievable with fully digital technology.
It provides tools necessary for operational monitoring tasks like checking signal validity and content quality, setting levels, and verifying signal paths, all with the measurement accuracy, repeatability, and stability achievable with fully digital technology.
Product Weight: 12.13 lbs
Dimensions: 8.5"W x 5.25"H x 18.13"D
Technical Tools
PDF Documents
Manufacturer Specs
Serial Digital Video Interface
Video Inputs: 2 per card: only one active at a time
Input Type: 75 Ω BNC, internally terminated
Launch Amplitude Accommodation
800 mV ±10% for full specification
800 mV ±30% up to 20 dB cable attenuation
Jitter Tolerance: 0.4 UIp-p typical above 2 MHz
Return Loss: 15 dB to 1.5 GHz
Isolation Between Inputs: >45 dB to 1 GHz
Switched Serial Video Output
Format: 1.485 Gbps or 270 Mbps repeat of selected input
Output Level: 800 mVp-p ±5% into 75 Ω load
Return Loss: 15 dB to 1.5 GHz
Output Type: 75 Ω BNC
External Reference
Sync Format: NTSC, PAL, 1080i 50 Hz, 1080i 59.94 Hz, 1080i 60 Hz, 720p 59.94, 1080p 23.98 Hz, 1080p 24 Hz.
Input Type: 75 Ω BNC passive loop
Return Loss: 40 dB to 30 MHz
Hum: Operates with 500 mVp-p
Signal/Noise: Operates to 25 dB
Serial SD Only Monitor Output
Content Follows Active Input With Brightups: SD only digital version of RGB/Y'P'bP'r analog pix monitor output on Ref board.
Rate: 270 Mbps
Signal Level: 800 mV ±5% into 75 Ω
Return Loss: 20 dB, 5 MHz to 270 MHz
Output Type: 75 Ω BNC
Serial SD Only Monitor Output
Content Follows Active Input With Brightups: SD only digital version of RGB/Y'P'bP'r analog pix monitor output on Ref board.
Rate: 270 Mbps
Signal Level: 800 mV ±5% into 75 Ω
Return Loss: 20 dB, 5 MHz to 270 MHz
Output Type: 75 Ω BNC
Impedance: 75 Ω unbalanced
Active Video Accuracy: 700 mV ±5%p-p (Y'P'bP'r mode)
Black (Blanking) Output Level: 0 mV ±25 mV
Frequency Response: Y, G, B and R ±8% to 30 MHz
AES Audio Interface
Audio Inputs: 4 inputs, 8 audio channels, meets requirements of AES-3id-2001.
Input Type: 75 Ω BNC, internally terminated, unbalanced
Input Amplitude Range: 0.2 V to 2 Vp-p
Input Sample Rate: 32 k to 96 k samples/sec
Input Lock Range: >±5%, typical
Input Return Loss: Better than 25 dB from 0.1 to 6 MHz
Audio Outputs: Up to 8 audio channels from embedded audio only
Output Format: 48 kHz, 20 bit, meets requirements of SMPTE 276M-1995 (AES-3id-2001)
Output Amplitude Range: 0.9 V to 1.1 Vp-p into 75 Ω
Output Sample Rate: Locked to embedded sample rate (nominally 48 kHz)
Output Jitter: Meets AES3-1997
Output Return Loss: Better than 25 dB 0.1 to 6 MHz
Waveform Vertical Deflection
Vertical Measurement Accuracy Using Graticule or Cursor:
At 1x, ±0.5% of 700 mV full scale
At 5x, ±0.2% of 700 mV full scale
At 10x, ±0.1% of 700 mV full scale
Gain: 1x, 5x, 10x, variable
Variable Gain Range: 0.25x to 14x
Frequency Response for monochrome signals, R, G and B bandwidths equal Y bandwidth:
Luminance channel (Y): 50 kHz to 30 MHz ±0.5%
Chrominance channels (P'b, P'r): 50 kHz to 15 MHz ±0.5%
Waveform Horizontal Deflection
Sweep Accuracy: ±0.5%, all rates, fully digital system
Sweep Linearity: 0.2% of time displayed on screen, fully digital system
Rates: 1, 2, 3, 4 line or field, depending on mode
Line Select: Selected line in 1 line, selected first line in 2 line or parade
Eye Pattern Display
Type: Equivalent time sampler.
Signal Bandwidth: 50 kHz to 2.5 GHz at :3 dB point.
Timebase Jitter: (Note: in 1 kHz high pass filter): 70 ps, typical.
Eye Clock Bandwidth Accuracy: Actual:3 dB point within 10% of nominal.
Display Modes:
Overlay: Overlays all bits to form each eye opening, uUseful for observing peak jitter.
20 Eye: Displays eye relative to the parallel clock and line sync, useful for observing jitter correlated to line rate and word clock.
Jitter Display
Type: Demodulated recovered clock per SMPTE RP184
Digital Readout: Accuracy: <0.05 UI + 10%, typical, of reading for jitter frequencies from three times high-pass filter selection to 1 MHz
Note: High-pass filter selection is set in Jitter Waveform Mode.
Jitter Waveform Gain Error: <0.1 UI + 10%, typical, of reading for jitter frequencies from three times high-pass filter selection to 1 MHz.
Jitter Waveform High-pass Filter Selection: 10 Hz, 1 kHz, 10 kHz, 100 kHz
Jitter Output: 100 mV/UI, ±10% into 75Ω load
Jitter Frequency Response::3 dB at 5 MHz (typical)
RGB Gamut Error Detection
Detection Level:
High Limit: +630 mV to +756 mV in 1 mV steps
Low Limit::50 mV to +35 mV in 1 mV steps
Arrowhead (NTSC/PAL Composite Gamut Limit Display Mode)
Detection Level Accuracy: ±7 mV
Luma+Chroma High Limit (NTSC-derived formats), 90 IRE to 135 IRE in 1 IRE steps
Luma+Chroma Low Limit (NTSC-derived formats),:50 IRE to:10 IRE in 1 IRE steps
Luma+Chroma High Limit (PAL-derived formats), 630 mV to 950 mV in 1 mV steps
Luma+Chroma Low Limit (PAL-derived formats),:400 mV to:100 mV in 1 mV steps
Luma only High Limit, 90% to 108% in 1% steps
Luma only Low Limit, 6% to +5% in 1% steps
Audio Level Meter
Level Meter Resolution: 0.05 dB steps at 10 dB scale, from full scale to:40 dB FS.
0.25 dB steps at 0 to:70 dB scale, for signals above:40 dB FS.
Level Meter Accuracy: 0.2 dB from 20 Hz to 20 kHz with 0 to -40 dB FS sine-wave input. PPM Ballistic mode except within 7 Hz of some submultiples of the 192 kHz oversampling frequency.
For example:
13.714 kHz ±7 Hz: 0.22 dB
16.0 kHz ±7 Hz: 0.30 dB
19.2 kHz ±7 Hz: 0.43 dB (worst case)
Power
Mains Voltage Range: 100 to 240 VAC ±10%
Mains Frequency: 50 or 60 Hz
Power Consumption (typical):
≤100 W with 1 Video Input Module
≤125 W with 2 Video Input Modules
150 W max
Connectors
VGA O/P: This connector allows the front panel display to be replicated on a remote VGA monitor.
Ethernet Connector: Allows the instrument to be connected to a 10/100Base-T Ethernet circuit for
remote control and firmware update.
Environmental
Temperature
32 ºF to +104 ºF (operating).
–4ºF to +140ºF (nonoperating).
Humidity: 20% to 80% RH at up to 40 ºC, noncondensing (operating).
Altitude:
to 9843 ft. (operating).
to 40,000 ft.(nonoperating).
Safety
Designed and tested for compliance with ANSI/ISA s82.02.01, Can/CSA C22.2 No. 1010.1, IEC 61010-1, UL 3111-1, 93/68/EEC and EN 61010-1.
EMI
Tested for compliance with:
FCC, CFR Title 47, part 15, Subpart B, Class A
EN 55103-1/2, Class B emissions
European EMC directive, video standard
Video Inputs: 2 per card: only one active at a time
Input Type: 75 Ω BNC, internally terminated
Launch Amplitude Accommodation
800 mV ±10% for full specification
800 mV ±30% up to 20 dB cable attenuation
Jitter Tolerance: 0.4 UIp-p typical above 2 MHz
Return Loss: 15 dB to 1.5 GHz
Isolation Between Inputs: >45 dB to 1 GHz
Switched Serial Video Output
Format: 1.485 Gbps or 270 Mbps repeat of selected input
Output Level: 800 mVp-p ±5% into 75 Ω load
Return Loss: 15 dB to 1.5 GHz
Output Type: 75 Ω BNC
External Reference
Sync Format: NTSC, PAL, 1080i 50 Hz, 1080i 59.94 Hz, 1080i 60 Hz, 720p 59.94, 1080p 23.98 Hz, 1080p 24 Hz.
Input Type: 75 Ω BNC passive loop
Return Loss: 40 dB to 30 MHz
Hum: Operates with 500 mVp-p
Signal/Noise: Operates to 25 dB
Serial SD Only Monitor Output
Content Follows Active Input With Brightups: SD only digital version of RGB/Y'P'bP'r analog pix monitor output on Ref board.
Rate: 270 Mbps
Signal Level: 800 mV ±5% into 75 Ω
Return Loss: 20 dB, 5 MHz to 270 MHz
Output Type: 75 Ω BNC
Serial SD Only Monitor Output
Content Follows Active Input With Brightups: SD only digital version of RGB/Y'P'bP'r analog pix monitor output on Ref board.
Rate: 270 Mbps
Signal Level: 800 mV ±5% into 75 Ω
Return Loss: 20 dB, 5 MHz to 270 MHz
Output Type: 75 Ω BNC
Impedance: 75 Ω unbalanced
Active Video Accuracy: 700 mV ±5%p-p (Y'P'bP'r mode)
Black (Blanking) Output Level: 0 mV ±25 mV
Frequency Response: Y, G, B and R ±8% to 30 MHz
AES Audio Interface
Audio Inputs: 4 inputs, 8 audio channels, meets requirements of AES-3id-2001.
Input Type: 75 Ω BNC, internally terminated, unbalanced
Input Amplitude Range: 0.2 V to 2 Vp-p
Input Sample Rate: 32 k to 96 k samples/sec
Input Lock Range: >±5%, typical
Input Return Loss: Better than 25 dB from 0.1 to 6 MHz
Audio Outputs: Up to 8 audio channels from embedded audio only
Output Format: 48 kHz, 20 bit, meets requirements of SMPTE 276M-1995 (AES-3id-2001)
Output Amplitude Range: 0.9 V to 1.1 Vp-p into 75 Ω
Output Sample Rate: Locked to embedded sample rate (nominally 48 kHz)
Output Jitter: Meets AES3-1997
Output Return Loss: Better than 25 dB 0.1 to 6 MHz
Waveform Vertical Deflection
Vertical Measurement Accuracy Using Graticule or Cursor:
At 1x, ±0.5% of 700 mV full scale
At 5x, ±0.2% of 700 mV full scale
At 10x, ±0.1% of 700 mV full scale
Gain: 1x, 5x, 10x, variable
Variable Gain Range: 0.25x to 14x
Frequency Response for monochrome signals, R, G and B bandwidths equal Y bandwidth:
Luminance channel (Y): 50 kHz to 30 MHz ±0.5%
Chrominance channels (P'b, P'r): 50 kHz to 15 MHz ±0.5%
Waveform Horizontal Deflection
Sweep Accuracy: ±0.5%, all rates, fully digital system
Sweep Linearity: 0.2% of time displayed on screen, fully digital system
Rates: 1, 2, 3, 4 line or field, depending on mode
Line Select: Selected line in 1 line, selected first line in 2 line or parade
Eye Pattern Display
Type: Equivalent time sampler.
Signal Bandwidth: 50 kHz to 2.5 GHz at :3 dB point.
Timebase Jitter: (Note: in 1 kHz high pass filter): 70 ps, typical.
Eye Clock Bandwidth Accuracy: Actual:3 dB point within 10% of nominal.
Display Modes:
Overlay: Overlays all bits to form each eye opening, uUseful for observing peak jitter.
20 Eye: Displays eye relative to the parallel clock and line sync, useful for observing jitter correlated to line rate and word clock.
Jitter Display
Type: Demodulated recovered clock per SMPTE RP184
Digital Readout: Accuracy: <0.05 UI + 10%, typical, of reading for jitter frequencies from three times high-pass filter selection to 1 MHz
Note: High-pass filter selection is set in Jitter Waveform Mode.
Jitter Waveform Gain Error: <0.1 UI + 10%, typical, of reading for jitter frequencies from three times high-pass filter selection to 1 MHz.
Jitter Waveform High-pass Filter Selection: 10 Hz, 1 kHz, 10 kHz, 100 kHz
Jitter Output: 100 mV/UI, ±10% into 75Ω load
Jitter Frequency Response::3 dB at 5 MHz (typical)
RGB Gamut Error Detection
Detection Level:
High Limit: +630 mV to +756 mV in 1 mV steps
Low Limit::50 mV to +35 mV in 1 mV steps
Arrowhead (NTSC/PAL Composite Gamut Limit Display Mode)
Detection Level Accuracy: ±7 mV
Luma+Chroma High Limit (NTSC-derived formats), 90 IRE to 135 IRE in 1 IRE steps
Luma+Chroma Low Limit (NTSC-derived formats),:50 IRE to:10 IRE in 1 IRE steps
Luma+Chroma High Limit (PAL-derived formats), 630 mV to 950 mV in 1 mV steps
Luma+Chroma Low Limit (PAL-derived formats),:400 mV to:100 mV in 1 mV steps
Luma only High Limit, 90% to 108% in 1% steps
Luma only Low Limit, 6% to +5% in 1% steps
Audio Level Meter
Level Meter Resolution: 0.05 dB steps at 10 dB scale, from full scale to:40 dB FS.
0.25 dB steps at 0 to:70 dB scale, for signals above:40 dB FS.
Level Meter Accuracy: 0.2 dB from 20 Hz to 20 kHz with 0 to -40 dB FS sine-wave input. PPM Ballistic mode except within 7 Hz of some submultiples of the 192 kHz oversampling frequency.
For example:
13.714 kHz ±7 Hz: 0.22 dB
16.0 kHz ±7 Hz: 0.30 dB
19.2 kHz ±7 Hz: 0.43 dB (worst case)
Power
Mains Voltage Range: 100 to 240 VAC ±10%
Mains Frequency: 50 or 60 Hz
Power Consumption (typical):
≤100 W with 1 Video Input Module
≤125 W with 2 Video Input Modules
150 W max
Connectors
VGA O/P: This connector allows the front panel display to be replicated on a remote VGA monitor.
Ethernet Connector: Allows the instrument to be connected to a 10/100Base-T Ethernet circuit for
remote control and firmware update.
Environmental
Temperature
32 ºF to +104 ºF (operating).
–4ºF to +140ºF (nonoperating).
Humidity: 20% to 80% RH at up to 40 ºC, noncondensing (operating).
Altitude:
to 9843 ft. (operating).
to 40,000 ft.(nonoperating).
Safety
Designed and tested for compliance with ANSI/ISA s82.02.01, Can/CSA C22.2 No. 1010.1, IEC 61010-1, UL 3111-1, 93/68/EEC and EN 61010-1.
EMI
Tested for compliance with:
FCC, CFR Title 47, part 15, Subpart B, Class A
EN 55103-1/2, Class B emissions
European EMC directive, video standard